Before Each Use Or As Required Check engine oil. Check hardware. Adjust belt guides. Replace auger drive belt. Replace traction drive belt. Replace shear bolt.

Snowblower Troubleshooting Section 55 - Specifications Snowblower Specifications Section 60 - Getting Quality Service Service Literature Parts Part Numbers John Deere Quality Continues with Quality Service. John Deere Trs32 Parts Manual John Deere TM1466 Technical Tech Manual TRS21 TRS24 TRS26 TRS32 WB Parts For John Deere Snowblowers TRS22 TRS24 TRS26 TRS27 TRS32. Select the Small Engine Repair Help for John Deere Snowblower While blowing snow I have looked at a parts diagram and there are.

Adjust chute worm drive. Adjust chute control rod. Adjust spout control lever. Adjust carburetor.

Adjust friction wheel. Replace friction wheel. Reverse scraper blade. Clean fuel cap vents. Check gearbox lubricant.

After First 2 Hours Of Operation Change engine oil. Check hardware.

Lubricate snowblower. Check auger drive belt adjustment. Check traction and auger cable adjustments.

10 Hours Lubricate snowblower 25 Hours Or At End Of Season Adjust auger drive belt Check spark plug. Change engine oil. Check tire pressure. Lubricate friction disk hub zerk. Check auger and traction cable adjustments. Lubricate auger shaft.

Lubricate wheel axle. Service Record.

TORQ-GARD SUPREME® (SAE 5W-30) The following John Deere oils are also recommended, based on their specified temperature range: TURF-GARD® (SAE 10W-30) PLUS-4® (SAE 10W-30) TORQ-GARD SUPREME® (SAE 30) Other oils may be used if above John Deere oil is not available, provided they meet one of the following specifications: SAE 5W-30-API Service Classification SG or higher SAE 10W-30-API Service Classification SG or higher SAE 30-API Service Classification SC or higher Grease Use grease based on the expected air temperature range during the service interval. The following greases are preferred: John Deere Moly High Temperature EP Grease. John Deere High Temperature EP Grease.

John Deere GREASE-GARD. Other greases may be used are: SAE Multipurpose EP Grease with 3 to 5 percent molybdenum disulfide. SAE Multipurpose EP Grease.

Greases meeting Military Specification MIL-G-10924C may be used as arctic grease. Clean vents (A) in nonflammable solvent.

Adjusting Carburetor NOTE: The carburetor is calibrated by the engine manufacturer and should not require any adjustments. Game gratis yang bisa pake joystick pc. If engine is operated at altitudes above 1829 m (6,000 ft.), some carburetors may require a special high altitude main jet. See your John Deere dealer. Possible engine surging will occur at high rpm when the machine is in neutral ('N') and the auger is disengaged.

This is a normal condition due to the emission control system. If engine is hard to start or runs rough, check the TROUBLESHOOTING section of this manual. After performing the checks in the troubleshooting section and your engine is still not performing correctly, contact your John Deere dealer. Checking Gearbox Lubricant Auger gearbox has been lubricated at factory and SHOULD NOT require additional lubrication. If for some reason the lubricant should leak out, or if the auger gearbox has been serviced; check lubricant.

Remove belt (F) from engine drive pulley (G). Remove top two housing bolts (H), and loosen bottom two bolts (I). Separate auger housing from engine frame hinging on bottom 2 bolts.

Remove brake arm (J) from housing. DO NOT remove spring. Remove old belt.

Position new belt on auger pulley. Install brake arm. Be sure brake arm is pushed into housing, and brake pad is seated in pulley groove. Position belt onto engine drive pulley. Install auger housing to engine frame with top two bolts.

Tighten bottom two bolts. (See Adjusting Auger Drive Belt in this section.) 14. Adjust belt guides. (See Adjusting Belt Guides in this section.) 15. Install cover.

Connect plug wire. Check auger drive cable adjustment. (See Adjusting Auger And Traction Drive Cable in this section.) Replacing Traction Drive Belt 1. Disconnect spark plug wire. Loosen nut (C) and move pulley away from auger drive belt (D). Take auger drive belt off of engine pulley (E). Pull and hold idler pulley (F) away from traction drive belt (G).

Pull belt past pulley. Remove belt from engine pulley. Remove belt from between bottom of large pulleys.